Мне привычно работать с тонкими отливками. В прошлый раз я заливал с 1,5% при 27 градусах и за несколько часов так и не дождался отверждения. Завтра попробую снизить пероксид до 1% и залить при 75 градусах, чтобы оценить его влияние на цвет.
Еще у меня вопрос к знающим, Trigonox C при 140 градусах без ускорителя сработает? Из описания я не смог понять.
Я почему подумал про кол-во пероксида, кроме того, что он является источником радикалов, у него еще сильные окислительные свойства и это может отчасти иметь (а может и не иметь) влияние на пожелтение.
Тригонокс С это перэфир ...
Перэфиры, перекисные аналоги сложных эфиров КС (О)—ООН, в основном используются как инициаторы высокотемпературной полимеризации. Их применение во многих случаях способствует образованию полимера с высоким молекулярным весом и хорошими показателями. Это относится, например, к блочной и суспензионной полимеризации стирола
и исходя из норионовского описания ...
Applications
Polymerization of styrene: Trigonox C may be used for the (co)polymerization of styrene in the temperature range of 100-140°C . In practice, combinations of two or more peroxides with diverging activities are used to reduce the residual monomer content in the final polymer and to increase reactor efficiency. Polymerization of ethylene: Trigonox C is an efficient initiator for the ethylene polymerization at high pressure in both autoclave and tubular processes. To obtain a wide spectrum of polymerization temperatures, Trigonox C is often used in combination with other peroxides. Depending on reaction conditions, Trigonox C is active in the temperature range of 220-270°C . Polymerization of acrylates and methacrylates: Trigonox C may be used as an initiator for the bulk, suspension and solution (co)polymerization of acrylates and methacrylates in the temperature range of 90-130°C . For Thermoset: Trigonox C, tert-butyl peroxybenzoate, is an aromatic perester, which is used for the curing of unsaturated polyester resins at elevated temperatures. Trigonox C is preferred for the curing of UP resin based Hot Press Moulding formulations (SMC, BMC etc.) in the temperature range of 120-170°C . Trigonox C can also be used in combination with high reactive peroxides like Perkadox 16 or Trigonox HMa as kicker in formulations for pultrusion in the temperature range of 100-150°C . In combination with a cobalt accelerator (e.g. Accelerator NL-53N, 10% cobalt), Trigonox C is also applicable for the cure of UP resins in the temperature range of 70°C and higher . Application area can be: air drying lacquers, diplacquers, filament winding, etc. For Crosslinking: Trigonox C is a monofunctional peroxide which is used for the crosslinking of natural rubber and synthetic rubbers, as well as polyolefins. Safe processing temperature: 100°C (rheometer ts2 > 20 min.). Typical crosslinking temperature: 140°C (rheometer t90 about 12 min.).
вроде как следует, что применение кобальтового 10% ускорителя с Тригонокс С применяется только в тех случаях, когда необходимо снизить нижний порог рабочей температуры инициирования (от 70°С). В остальных случаях его используют самостоятельно либо в комбинации с другими пероксидами и преимущественно при высоких температурах, вплоть до 270°С